[제품설명]
XTi2 Series는 Portable PA용으로 디자인되고 만들어진 프로페셔널용 앰프로, 출력파워가 다르다는 것을 제외
하고 4모델은 동일한 성능을 갖고 있습니다. XTi 1002, 2002, 4002 그리고 6002 모두 매우 튼튼하면서도 가볍고,
매우 뛰어난 성능을 갖고 있으며, 전면 판낼에 크로스 오버 주파수, EQ, Limiting, Delay 그리고 Subharmonic
Synthesizer를 조절할 수 있는 LCD스크린이 있다.
그 밖에도 전세계적으로 통용 가능한 전원 공급스위치모드, 기능성 인디케이터, 냉각을 돕는 스피드 팬, XLR
Inputs, Speakon 그리고 Binding Post 출력장치, 누전방지 등 많은 특징들을 갖고 있습니다.
게다가 당신의 XTi2에 대한 투자는 Crown의 3년간의 무과실 손해배상의 보증에 의해 지원됩니다.
[제품스펙]
|
|
6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
|
|
|
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
|
|
|
8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
|
|
|
For signal alignment of driver; 50 mS of total delay.
|
|
|
Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
|
|
|
User defeatable limiter that allows users to control Threshold, Attack, and Release times.
|
|
|
50 total presets, 49 of which are user-definable.
|
Sensitivity (for full rated power at 4 ohms)
|
|
Frequency Response (at 1 watt, 20 Hz - 20 kHz)
|
|
Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms)
|
XTi1002/2002/4002: 100 dB (A weighted)
XTi6002: 103 dB (A weighted)
|
Total Harmonic Distortion (THD)
|
|
Damping Factor 20 Hz to 1 kHz
|
|
Crosstalk (below rated power)
|
|
Input Impedance (nominal)
|
20k ohms balanced, 10k ohms unbalanced
|
|
|
|
AC Line Voltage and Frequency Configurations
|
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
|
AC Line Current
(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)
|
XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle
|
|
|
0°C to 40°C at 95% relative humidity (non-condensing)
|
|
|
Two front-panel rotary level controls, one for each channel
|
|
|
On/Off switch applies AC power to the amplifier
|
|
|
Three buttons near the LCD screen that are used to access menu items and front panel lockout
|
|
|
Backlit liquid crystal display that shows preset and processing status
|
|
|
Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
|
|
|
Green LED flashes when output signal exceeds -10 dB below clip.
|
|
|
Green LED flashes when output signal level exceeds -20 dB below clip.
|
|
|
Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
|
|
|
Red LED, one per channel, turns on at the threshold of audible distortion
|
|
|
Red LED, one per channel, illuminates under excessive temperature conditions
|
|
|
Blue LED illuminates when the amplifier has been turned on and has power
|
| |
|
현재위치 : 
